How Do You Chang The Passenger Side Low Beam Bulb On A 2005 Ford Expedition

Ford Expedition Headlight Bulbs Replacement Guide
How to replace the high beam, low beam, and parking / turn signal calorie-free bulbs in a 2003-2006 Ford Expedition SUV.

Ford Expedition Headlight
Removing 10mm Bolt
2nd 10mm Bolt This automotive how-to guide was specifically written to assist owners of the 2003, 2004, 2005 and 2006 Ford Trek SUV in replacing a burnt out low axle, high beam, or parking / turn indicate calorie-free seedling in the headlight assembly.

Owners of other similar Ford vehicle models such as the Explorer, Lincoln Navigator, F-150, Lightning, Excursion, Escape, Bronco, and Sport Trac may too notice these instructions to be useful.

Replacement lite bulbs from Sylvania and other manufacturers have the following part numbers: Low Beam # 9006, Loftier Beam # 9005 and Front Turn Signal / Parking # 3357.

The only tool needed to replace any bulb in the headlight associates of a 2003-2006 Ford Trek is a 10mm socket and ratcheting wrench.

Two 10mm Bolts Removed
Headlight Bolts Removed
Concord Dorsum Front Bumper The easiest manner to access the light bulbs in the headlight assembly of a Ford Expedition is to remove the two 10mm bolts that secure it to the front of the vehicle.

One time the 2 bolts are removed, you tin can gently concord back the center part of the forepart bumper that obstructs the headlight assembly.

So pull the entire assembly out and residue it on a towel or rag to prevent scratching the painted upper lip of the bumper.

Pull Out Headlight
High & Low Dust Covers
Depression Beam Front end At the centre rear of the headlight assembly, y'all'll run into a large round dust cover that protects the low axle headlight bulb and socket.
Low Beam Dust Cover
Pull Off Grit Boot
Turn Counter Clockwise Pull or pare off the low beam dust cover past grapping the outer lip or by using the ii rubber pull tabs.

So grasp the base of operations of the low beam headlight, plow it i/4 turn counter clockwise, and pull information technology straight out from the associates.

# 9006 Low Axle Bulb
Pry Upwardly Grey Plastic Clip To disassemble the low beam headlight's base from the ability connector, pry up the light grey plastic prune with a flathead screwdriver or your fingertips and wiggle the connector direct off the base of the bulb.
Sylvania 9006 ST HB4
Insert Into Headlight
ane/four Turn Counter Clockwise Replace the one-time # 9006 low beam bulb with a new ane, attach the power connector, insert it into the headlight, and turn it one/iv plough clockwise to secure it.
Front - High Beam Bulb
Pull Off Grit Cover
# 9005 High Beam Socket The loftier beam headlight bulb is located closest to the centre line of the vehicle and is protected by a smaller circular rubber dust embrace.

Peel off the rubber dust boot to admission the # 9005 high beam bulb.

To remove information technology, plow the bulb's base one/4 turn counter clockwise and pull it direct out from the headlight associates.

Twist 1/4 Turn Clockwise
High Beam Removed
Pry Up Black Plastic Clip To divide the calorie-free bulb from the power connector, pry up the black plastic retaining prune with a flathead screwdriver or your fingertips and pull information technology straight off from the light seedling's base of operations.

Replace the high beam bulb with a new # 9005, snap on the ability connector, insert the seedling into the headlight, and turn it 1/4 plow clockwise to secure it.

Front end - Parking / Turn Signal
Turn Indicate Bulb Socket
1/four Turn Counter Clockwise The front end turn indicate (parking) light seedling is located at the outer edge of the headlight assembly.

Plow the socket 1/4 turn counter clockwise and pull it direct out from the assembly.

Pull the sometime # 3357 light bulb straight out from the socket.

If it won't come up out easily, try fluctuant information technology while pulling.

Supplant it with a new articulate 3357 seedling, insert the bulb into the headlight associates, and turn information technology 1/4 turn clockwise to secure information technology.

Remove Ability Connector
Pull Out Socket & Bulb
Wiggle Out # 3357 Bulb Test the new light bulbs past turning on the headlights, activating the adventure signals and flashing the high beams.

For more of my related automotive guides or reviews, click on the post-obit links: Ford Trek 5.4L V8 Engine OIl Modify Guide, Ford Expedition Tail Light Bulbs Replacement Guide, Ford Trek Overhead Map Light Bulbs Replacement Guide, Meguiar's Headlight Restoration Kit Review, WeatherTech FloorLiner Mats Review, Machine Headlight / Tail Light Condensation Repair Guide, Sunforce Solar Battery Maintainer, Corroded Machine Bombardment Final Replacement Guide, Garmin Nuvi 260W GPS Review, Car Interior Carpet Replacement Guide, Buffing Old Faded Headlights Guide, Thousand&N Air Filter Cleaning Guide, and Zaino Bros Show Car Smooth Review.

Source: https://www.paulstravelpictures.com/Ford-Expedition-Headlight-Bulbs-Replacement-Guide/

Posted by: mintonglage1957.blogspot.com